Rubber & Plastic Products

Natural Pigments Withstand PLA and PBS Compounding, but Light Stability Remains the Limit

Masterbatch trials with spirulina, curcumin, beetroot and chlorophyllin show conventional extrusion and molding are viable, while UV exposure remains the weak point.

Nadia SorensenNovember 2, 20265 min read2 views

Four colored polymer strands leaving a twin-screw extruder die head and cooling in a water trough on a laboratory bench.

A study of four commercial natural colorants has found that most can be compounded into polylactic acid (PLA) and polybutylene succinate (PBS) on conventional twin-screw extrusion and injection-molding equipment, with only modest changes to melt flow and mechanical behavior. The main constraints are thermal degradation during processing and limited color stability in service.

The work, titled "Sustainability in the Development of Natural Pigment-Based Colour Masterbatches and Their Application in Biopolymers," used blue spirulina, yellow curcumin, red beetroot and green chlorophyllin. Each pigment was combined with PLA and PBS to produce color masterbatches by twin-screw extrusion, with titanium dioxide, calcium carbonate and stearic acid added to support UV protection, dispersion and processing. The masterbatches were then diluted into the matching polymer matrix at 2, 4 and 6 wt% and injection molded into test specimens.

Thermal window defines the limits

Thermogravimetric analysis placed degradation onset at roughly 229 °C for spirulina, 244 °C for curcumin, 258 °C for chlorophyllin and 267 °C for beetroot — below the degradation temperatures of the two polyesters. The researchers therefore selected extrusion profiles that melted each matrix while limiting heat exposure to the pigments: 145 °C for PBS and 190 °C for PLA, with the twin-screw extruder running at 65 rpm and a feed rate of 2 kg/h.

That window suited most pigment–polymer combinations, but spirulina was the notable exception. During PLA processing it lost its characteristic blue, so no blue PLA masterbatch could be produced; PBS’s lower processing temperature left enough pigment intact for successful compounding. Pigment compatibility, the authors conclude, depends strongly on the thermal processing requirements of the matrix.

Small effects on flow and mechanics

Rheology changed little. Melt flow rate decreased slightly after pigment incorporation, indicating a modest rise in melt viscosity. Neat PLA measured about 50 g/10 min, and the natural-pigment masterbatches stayed close to that value; PBS responded similarly, with only a minor reduction.

That result matters for compounders, because a natural color system offers little practical value if it forces major changes to screw design, pressure settings or molding conditions. In this study, standard compounding and molding handled most formulations without significant processing problems.

Tensile and impact behavior were largely preserved across the 2 to 6 wt% addition range. PLA started from a Young’s modulus of about 1710 MPa and a tensile strength of 65.6 MPa; PBS started from about 392 MPa and 34.5 MPa respectively. The colored formulations stayed close to those baselines, and impact strength remained in a similar range, although individual pigments produced some variation.

Light stability is the largest barrier

Successful extrusion did not ensure durable color. After 50 hours of xenon-lamp exposure, most formulations exceeded a color difference of ΔE* = 2, a level generally treated as visually perceptible. The PLA formulation containing 2 wt% green chlorophyllin masterbatch was the main exception and showed the highest photostability.

The study therefore points to UV stability as the biggest obstacle to broader use. Packaging, consumer products, agricultural parts and outdoor applications may require additional stabilization, protective coatings or pigment modification before natural colors can compete with conventional systems over long service periods.

Lower carbon footprint under stated assumptions

The environmental comparison also favored the natural pigments. Under the study’s assumptions, one kilogram of curcumin pigment corresponded to about 0.04 kg CO2-eq, against 18.65 kg CO2-eq for the inorganic green reference pigment. The natural-pigment masterbatches also consumed less electricity during extrusion and pelletizing.

The authors conclude that natural colorants still need development, particularly in lightfastness and thermal stability, but that several can be compounded into PLA and PBS with conventional equipment and limited impact on melt viscosity and mechanical performance. Future work, they suggest, should focus on improving color stability during processing and subsequent service exposure.